Load ring for welding LBS-RS, Stainless Steel, without springA stainless steel load ring for welding made of the material 1.4571 (in welded condition resistant against inter-cristalline corrosion, in permanent operation up to 400°C). The chemical resistance and resistance against pitting by chloride media have increased due to the Mo contents. The material 1.4571 is widely used in the chemical industry, petroleum, coal-tar chemistry, and textile industries. Use the Castolin ARC A Mo90009N welding electrode or consult the manufacturer for the appropriate solution with respect to the work piece. Observe the requirements of DIN 8556 part 1. |
 |
ABA Weldable Lifting Point
ABA Weldable Lifting PointLoadable from any direction. Safety factor: 4:1 Quenched and tempered part, thereby wear resistant. Patentented wear markings, inside and outside. Circulating fillet weld. Surface phosphated. If component is used as lashing-point, stated WLL at the component can be doubled. |
 |
VABH-W Mounting Hook, Ready for Welding
Excavator hook welded VABH-WExcavator hook used as a lifting point for wire rope slings, round slings and lifting means with an oval suspension ring or eye. With a stable hook securing mechanism protected by a ridge, comparable to that of the VCGH. Thickened tip of the hook to avoid misuse, thus hooking into smaller openings is impossible. Patented wear marks on the hook. Pay attention to the permissible load direction. With a phosphated surface. Pay attention to the correct thickness of the weld. Welding should only be carried out by qualified persons according to EN 287-1. Material: 23MnNiCrMo52. |
 |
VCGH-S Mounting Hook, Ready for Welding
Excavator hook welded VCGH-S
|
 |
VRBK Load Ring Welded for 90°-Corners
Eye Plate for Corners VRBKAn enhancement of the well-established RBK-series with an over 30% increment of the WLL. A forged ring bracket according to EN1677-1. Even force distribution owing to the two point attachment. Low profile, since it can be folded within an angle range of 270°. The welding block for edges is forged out of a good welding material 1.0577+N (St 52-3) and clearly stamped with an identification number for the permissible WLL. |
 |
VRBS Welding Block
VRBS Welding block VASKThe welding blocks are forged out of the material 1.0577+N (St 52-3) and are marked with the identification number of the permissible nominal WLL. The patented distance lugs have a distance measurement function for the required spacing to the root weld (approximately 3 mm). Welding should be carried out by a qualified person according to EN 287-1. The chosen welding point must be suitable for the corresponding force introduction. Separate welding instructions for the welding procedure and filler metals are supplied with the VRBS. |
 |
VRBS Ring
VRBS-Ring VRLForged load ring according to EN 1677-1. 100% electromagnetic crack detected; pink powder coated. Meets the requirements of the respective employer’s liability insurance association. |
 |
VRBS Load Ring Welded
Eye Plate, ready for welding VRBSAn enhancement of the well established RBS series with an up to 30% increment of the WLL. The two points of attachment facilitate an even and optimal force distribution into the work piece, thus usage of thinner base plates is possible. A forged, pink coated ring bracket according to EN1677-1. The welding block is forged out of a good welding material 1.0577+N (St 52-3). Low profile, high dynamic, and static strength. The ring is stowable, thus avoiding the hazard of tripping. |
 |
VRBS-FIX Load Ring Welded
Load ring, for welding VRBS-FIXWeld-on parts without bothersome sub-surface corrosion due to circular HY-weld seam. Smaller weld seam compared to the previous VRBS. Total length and total width identical to the previous VRBS. No time-consuming alignment between the weld-on blocks and ring. Clamp spring is protected being placed inside the weld-on block. The spring fixes the weld-on blocks to the ring and creates, at the same time, a radial clamping. Clamping spring avoids rattling noise. Recognition of inclination angle indicated by markings on the ring and on the blocks in all levels. |
 |
VLBS Welding Block
Welding Block ASK-VLBSThe welding block is forged out of the material 1.0577+N (St 52-3) and is marked with the identification number of the permissible nominal WLL. The patented distance lugs have a distance measurement function for the required spacing to the root weld (approximately 3 mm). Welding should be carried out by a qualified person according to EN 287-1. The chosen welding point must be suitable for the corresponding force introduction. Separate welding instructions for the welding procedure and filler metals are supplied with the VLBS. |
 |